City of Delafield Public Works
2020 1-Ton Truck Equipment Specifications
The City of Delafield Public Works Department is requesting sealed bids for the following equipment and installation of said equipment on a 2020 Ford Super Duty F-550 DRW chassis supplied by the City of Delafield. The bidder shall bid all items requested in order to qualify for an awarded bid. The City of Delafield Public Works Department reserves the right to accept or reject any or all bids. Bids are due to the City of Delafield City Hall by noon on January 16th. 2019. Please mark the bid “Public Works Truck Equipment Bid” Any questions on the specifications please call Paul Zellner at 262-303-4627.
2019 Truck Equipment Minimum Specifications
Any equipment that is bid other than the specified brand must be at least equal to the specified equipment. The City of Delafield will determine if the equipment is equal to the specifications. The City of Delafield reserves the right to accept or reject any or all bids.
Henderson Mark III, Crysteel Select or MTEZee - 9’, 3-4 yard Stainless Steel Dump Body with class D subframe hoist with power down (no exceptions) western style understructure, box construction to be a min. of 10 ga. 201stainless steel, 3/16” AR400 floor, 18” sides with side board pockets, cab protector
24”Tailgate to include a quick release mechanism for easy opening of top pins
Grease fittings on tailgate linkage and locking lobs
Body left in bare stainless steel, 2B finish (no sand blasted finishes)
Box indicator light mounted in the cab to remind operator that the box is up
1-Fold down stainless steel 2-rung ladder mounted for easy access into the dump body (location to be determined at time of build)
1-Stainless Steel grab handle near the fold down ladder for easy access into the dump body (location to be determined at time of build)
2-Stainless Steel –spring loaded shovel holders –one mounted on each side of dump body (location to be determined at time of build.
Minimizor poly rear fenders with stainless steel mounting brackets and built in L.E.D. stop, turn lights
Trailer tow plate to include receiver for class V hitches, safety chain connector points and a 7 wire RV trailer plug with flat prongs mounted in plate and wired to factory supplied trailer brake controller
Stainless Steel removable tailgate wings to hold tailgate open when salt spreader unit is installed to hold tailgate open and prevent material spillage
1-Federal Signal Highlighter #454201-25 LED amber light with clear lens mounted above cab protector
4-Piranha amber LED strobe lights (2) mounted on the cab protector facing to the rear in stainless steel enclosure & (2) recessed in the rear corner posts
LED body and parking lights
1-amber sanding light mounted on left side of auger unit, includes quick connect plug for easy removal
1-L.E.D. back up light mounted on right side of auger unit, includes quick connect plug for easy removal.
STAINLESS STEEL UNDER TAILGATE MOUNTED SALT SPREADER
Henderson model #TGS or Monroe model #MS966-OW-GB-SS
7-Gauge trough and lid
Fully opening top lid with easy access
Fully opening bottom trough for assisting with complete clean out of unit
Center lift handle
Anti-flow plate to restrict material from free flowing when unit is stopped
Auger diameter- 6”
Shaft- 1 ¼”
Gear box driven hydraulic auger
Internal road speed sensor
Western MVP3 9’ 6” Steel with rubber snow deflector or Boss 9’ 2” Power-V DXT steel with rubber snow deflector.
Snowplow to be operated by its own hydraulic power unit, not to be plumbed off of truck hydraulic system.
Snowplow package shall include complete plow, harness, lighting, controls, and power unit.
Force America 5100EX controls- to control dump body, spreader and spinner
Muncie P.TO. and direct mount pump transmission mounted off of transmission to power hydraulics for- dump body, spreader & spinner
Seamless stainless steel hydraulic lines with short whip hoses will be used to plumb hydraulics to - dump body, spreader and spinner
Hydraulic Gear Pump / Hot Shift PTO- Parker / Chelsea 249 Series
PTO shall be engaged / disengaged from the cab by a 12 VDC on / off switch
Combination hydraulic reservoir / valve enclosure to be stainless steel, frame mounted driver side with a 15 gallon capacity. The reservoir must be equipped with the following- ¾” magnetic drain plug, 1 ¼” full flow brass ball valve, 2” x 1 ¼” NPT suction strainer with 100 mesh screen and 3 PSI bypass valve, tank mount return line filter with a built in breather, and site temperature gauge externally mounted facing front of truck. The enclosure lid will be removable by one person without the use of tools.
Hydraulic Control Valve- shall be a modular stackable manifold with level port design. Each hydraulic function requires an individual manifold be stacked together to form the manifold base. An adjustable main relief will be contained within the inlet to limit the system pressure. Each hydraulic valve section must be serviceable without removing any hydraulic hoses or any other hydraulic components
MANUALS & WARRANTIES
1. One set of service, parts, overhaul, repair, and wiring diagram manuals are to be furnished with the equipment. (C.D. or Wed based allowed)
2. Coordination shall be maintained at all times between the City of Delafield and Equipment vendor on all phases of assembly. All equipment is to be positioned and mounted to the complete satisfaction of the City of Delafield.
3. Equipment warranty on parts and labor to be one year.
Truck Equipment Bid $_____________
1. Days From Receipt of Order to Delivery: Days
2. Your Terms This Order: Days
3. This Quotation Good For: Days